Restore your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are experiencing unexpected issues. Fortunately, resetting your Holosun is a simple process that can be completed in just a few procedures.

• Begin by ensuring your red dot sight is activated.
• Find the small reset button on the bottom of the sight.
• Use a paperclip to depress the reset switch for approximately 5 milliseconds.
• Let go the switch and your Holosun EPS Carry Red Dot sight will power cycle.
• Its red dot sight should now be reverted to its factory settings.

Reset Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it back to standard configuration is a breeze. First, determine the tiny button on the rear of your optic. Then, press and hold it for around ten seconds until you see the red dot blink. Your Holosun EPS Carry is now reverted to its factory settings, ready for consistent targeting.

restore Your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent accidental activation during here the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

• Press and hold the power button for approximately 5 seconds.
• A message will flash, indicating that the reset is being performed.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and verify your sight's functionality. If you encounter any further troubles, don't hesitate to seek help from Holosun's support.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

• Initially, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• As you continue holding these buttons, tap the power button once.
• The display will show a confirmation prompt indicating that the reset process is initiated.
• Permit the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reset your Holosun EPS Carry via a Factory Default Settings

If your Holosun EPS Carry is acting up, a factory reset might be the answer. This will return your sight to its factory settings, clearing any custom configurations you've made. To perform this reset, adhere to these straightforward steps:

• To begin, locate the reset switch on your EPS Carry.
• Then, engage a fine object, like a paperclip, to depress the reset button.
• As you maintain the reset switch engaged, turn your EPS Carry.
• The sight will display a message confirming that the reset is complete.

Once the reset is successful, your EPS Carry will be set to its factory settings.

Report this wiki page